Cisco认证实验考试经典题库CCIE_BootCamp3.0(第十章)

137.20.0.0/24 is subnetted, 1 subnets c 137.20.20.0 is directly connected, ethernet 0 172.168.0.0/16 is variably subnetted, 7 subnets, 2 masks o ia 172.168.30.0/24 [110/65] via 172.168.100.3, 00:09:03, serial 1.1 i 172.168.40.0/24 [100/8576] via 172.168.200.2, 00:01:11, serial 1.2 o ia 172.168.60.0/24 [110/1572] via 172.168.65.1. 00:09:03, bri0 c 172.168.65.0/24 is directly connected, bri0 c 172.168.100.0/24 is directly connected, serial 1.1 o 172.168.100.0/24 [110/64] via 172.168.100.3, 00:09:13, serial 1.1 c 172.168.200.0/24 is directly connected, serial 1.2 o e1 192.168. 21.0/24 [110/21] via 137.20.20.1. 00:09:03, ethernet 0 o e1 192.168. 17.0/24 [110/21] via 137.20.20.1. 00:09:03, ethernet 0 o e1 192.168. 70.0/24 [110/21] via 137.20.20.1. 00:09:03, ethernet 0 o*e1 0.0.0.0/0 [110/21] via 137.20.20.1. 00:09:03, ethernet 0 r5#show ip ospf int bri0 bri0 is up, line protocol is up (spoofing) internet address 172.168.65.2/24, area 10 process id 1, router id 172.168.200.1, network type point_to_point, cost 1562 run as demand circuit donotage lsa allowed. transmit delay is 1 sec, state point_to_point, timer intervals configured, hello 10, dead 40, wait 40, retransmit 5 hello due in 00:00:06 neighbor count is 1, adjacent neighbor count is 1 adjacent with neighbor 172.168.100.6 (hello suppressed) suppress hello for 1 neighbor(s) r5#show dialer bri0 – dialer type =isdn dial string successes failures last called last status 4930622 1 0 00:08:45 successful 0 incoming call(s) have been screened 0 incoming call(s) rejected for callback bri0:1 – dialer type =isdn idle time(45 secs), fast idle timer (20 secs) wait for carrier (30 secs), re-enable (15 secs) dialer state is idle bri0:2 – dialer type =isdn idle time(45 secs), fast idle timer (20 secs) wait for carrier (30 secs), re-enable (15 secs) dialer state is idle r5# now go back to router r7 and bring up router r7’s interface s4 again 3. ipx configuration –15 pts (1 hour) a. configure all the active interfaces, including loopbacks, on routers r1, r2, r3, r5, r6, and r8 for ipx. b. configure router r8 and the lan interfaces on routers r3, r4, r5 and r6 for ipx rip. c. configure router r1 & r2 for ipx nlsp. d. configure the serial interfaces on the rest of the routers for ipx eigrp( not routers r1& r2 these oly use nlsp), also make the ethernet interface on router r2 ipx eigrp only. e. configure the bri0 interfaces on routers r5 & r6 as ipx rip. f. after this point you should be able to see all the ipx networks in all the routers routing table. test connectivity with ipx ping.